DC/AC inverters convert DC source energy for AC users, and are a big category of power electronics. Power electronics is the technology to process and control the flow of electric energy by supplying voltages and currents in a form that is optimally suited for user loads [1]. A typical block diagram is shown in Figure 1.1 [2]. The input power can be AC and DC sources. A general example is that the AC input power is from the electric utility. The output power to load can be AC and DC voltages. The power processor in the block diagram is usually called a converter. Conversion technologies are used to construct converters. Therefore, there are four categories of converters [3]:
• AC/DC converters/rectifiers (AC to DC)
• DC/DC converters (DC to DC)
• DC/AC inverters/converters (DC to AC)
• AC/AC converters (AC to AC)
We will use converter as a generic term to refer to a single power conversion stage that may perform any of the functions listed above. To be more specific, in AC to DC and DC to AC conversion, rectifier refers to a converter when the average power flow is from the AC to the DC side. Inverter refers to the converter when the average power flow is from the DC to the AC side. In fact, the power flow through the converter may be reversible. In that case, as shown in Figure 1.2 [2], we refer to that converter in terms of its rectifier and inverter modes of operation.
1.1 Symbols and Factors Used in This Book
We list the factors and symbols used in this book here. If no specific description is given, the parameters follow the meaning stated here.
1.1.1 Symbols Used in Power Systems
For instantaneous values of variables such as voltage, current, and power that are functions of time, the symbols used are lowercase letters v, i, and p, respectively. They are functions of time operating in the time domain. We may or may not explicitly show that they are functions of time, for example, using v rather than v(t). The uppercase symbols V and I refer to their average value in DC quantities and a root-mean-square (rms) value in AC quantities, computed from their instantaneous waveforms. They generally refer to an average value in DC quantities and a root-mean-square (rms) value in AC quantities. If there is a possibility of confusion, the subscript avg or rms is used. The average power is always indicated by P.
Usually, the input voltage and current are represented by vin and iin (or v1 and i1), and the output voltage and current are represented by vO and iO (or v2 and i2). The input and output powers are represented by Pin and PO. The power transfer efficiency (η) is defined as η = PO/Pin.
Passive loads such as resistor R, inductor L, and capacitor C are generally used in circuits. We use R, L, and C to indicate their symbols and values as well. All these parameters and their combination Z are linear loads since the performance of the circuit constructed by these components is described by a linear differential equation. Z is the impedance of a linear load. If the circuit consists of a resistor R, an inductor L, and a capacitor C connected in series, the impedance Z is represented by
(1.1) |
where R is the resistance measured by Ω, L is the inductance measured by H, C is the capacitance measured by F, ω is the AC supply angular frequency measured by rad/s, and ω = 2πf, where f is the AC supply frequency measured by Hz. For the calculation of Z, if there is no capacitor in the circuit, the term j1ωC
|Z|=√R2+(ωL−1ωC)2ϕ=tan−1ωL−1ωCR |
(1.2) |
Example 1.1
A circuit has a load with a resistor R = 20 Ω, an inductor L = 20 mH, and a capacitor C = 200 μF in series connection. The voltage supplying frequency f = 60 Hz. Calculate the load impedance and the phase angle.
Solution:
From Equation (1.1), the impedance Z is
Z=R+jωL−j1ωC=20+j120π×0.02−j1120π×0.0002=20+j(7.54−13.26)=20−j5.72=|Z|<ϕ
From Equation (1.2), the absolute impedance |Z| and phase angle φ are
|Z|=√R2+(ωL−1ωC)2=√202+5.722=20.8Ωϕ=tan−1ωL−1ωCR=tan−1−5.7220=−17.73∘
If a circuit consists of a resistor R and an inductor L connected in series, the corresponding impedance Z is represented by
(1.3) |
The absolute impedance |Z| and phase angle φ are determined by
(1.4) |
We define the circuit time constant τ as
(1.5) |
If a circuit consists of a resistor R and a capacitor C connected in series, the impedance Z is represented by
(1.6) |
The absolute impedance |Z| and phase angle φ are determined by
|Z|=√R2+(1ωC)2ϕ=−tan−11ωCR |
(1.7) |
We define the circuit time constant τ as
(1.8) |
Symbol |
Explanation (Measuring Unit) |
C |
capacitor/capacitance (F) |
f |
frequency (Hz) |
i, I |
instantaneous current, average/rms current (A) |
L |
inductor/inductance (H) |
R |
resistor/resistance (Ω) |
p, P |
instantaneous power, rated/real power (W) |
q, Q |
instantaneous reactive power, rated reactive power (VAR) |
s, S |
instantaneous apparent power, rated apparent power (VA) |
v, V |
instantaneous voltage, average/rms voltage (V) |
Z |
impedance (Ω) |
φ |
phase angle (degree, or radian) |
η |
efficiency (percents%) |
τ |
time constant (second) |
ω |
angular frequency (radian/sec), ω = 2πf |
1.1.2 Factors and Symbols Used in AC Power Systems
The input AC voltage can be single-phase or three-phase voltages. They are usually a pure sinusoidal wave function. For a single-phase input voltage v(t), the function can be expressed as [4]:
(1.9) |
where v is the instantaneous input voltage, V is its root-mean-square (rms) value, Vm is its amplitude, ω is the angular frequency, ω = 2πf, and f is the supply frequency. Usually, the input current may not be a pure sinusoidal wave, depending on the load. If the input voltage supplies a linear load (resistive, inductive, capacitive loads, or their combination) the input current i(t) is not distorted, but may be delayed in a phase angle φ. In this case, it can be expressed as
i(t)=√2I sin (ωt-ϕ) = Im sin (ωt−ϕ) |
(1.10) |
where i is the instantaneous input current, I is its root-mean-square value, Im is its amplitude, and φ is the phase-delay angle. We define the power factor (PF) as
(1.11) |
PF is the ratio of the real power (P) to the apparent power (S). We have the relation S = P + jQ, where Q is the reactive power. The power vector diagram is shown in Figure 1.3. We have the following relations between the powers:
(1.12) |
(1.13) |
(1.14) |
(1.15) |
(1.16) |
If the input current is distorted, it consists of harmonics. Its fundamental harmonic can be expressed as
i1=√2 I1sin(ωt−ϕ1)=Im1sin(ωt−ϕ1) |
(1.17) |
where i1 is the fundamental harmonic instantaneous value, I1 its rms value, Im1 its amplitude, and φ1 its phase angle. In this case, the displacement power factor (DPF) is defined as
(1.18) |
Correspondingly, the power factor is defined as
(1.19) |
where THD is the total harmonic distortion. It can be used to measure both voltage and current waveforms. It is defined as
THD=√∑∞n=2I2nI1 or THD =√∑∞n=2V2nV1 |
(1.20) |
where In or Vn is the amplitude of the nth order harmonic.
The harmonic factor (HF) is a variable that describes the weighted percentage of the nth order harmonic with reference to the amplitude of the fundamental harmonic V1. It is defined as
(1.21) |
n = 1 corresponds to the fundamental harmonic. Therefore, HF1 = 1. The total harmonic distortion (THD) can be written as
(1.22) |
A pure sinusoidal waveform has THD = 0.
Weighted total harmonic distortion (WTHD) is a variable to describe waveform distortion. It is defined as follows:
(1.23) |
Note that THD gives an immediate measure of the inverter output voltage waveform distortion. WTHD is often interpreted as the normalized current ripple expected in an inductive load when fed from the inverter output voltage.
Example 1.2:
A load with a resistor R = 20 Ω, an inductor L = 20 mH, and a capacitor C = 200 μF in series connection is supplied by an AC voltage of 240 V (rms) with frequency f = 60 Hz. Calculate the circuit current and the corresponding apparent power S, real power P, reactive power Q, and the power factor PF.
Solution:
From Example 1.1, the impedance Z is
Z=R+jωL-j1ωC=20+j120π×0.02−j1120π×0.0002=20+j(7.54−13.26)=20−j5.72=20.8<−17.73∘Ω
The circuit current I is
l=VZ=24020.8<−17.73∘=11.54<17.73∘A
The apparent power S is
S=Vl*=240×11.54<−17.73∘=2769.23<−17.73∘VA
The real power P is
P=|S|cosϕ = 2769.23×cos17.73∘=2637.7W
The reactive power Q is
Q=|S|sinϕ = 2769.23×sin-17.73∘=843.3VAR
The power factor is
PF=cos ϕ=0.9525 Leading
Symbol |
Explanation (Measuring Unit) |
DPF |
displacement power factor (percent) |
HFn |
nth order harmonic factor |
i1, I1 |
instantaneous fundamental current, average/rms fundamental current (A) |
in, In |
instantaneous nth order harmonic current, average/rms nth order harmonic current (A) |
Im |
current amplitude (A) |
PF |
power factor (leading/lagging percent) |
q, Q |
instantaneous reactive power, rated reactive power (VAR) |
s, S |
instantaneous apparent power, rated apparent power (VA) |
t |
time (second) |
THD |
total harmonic distortion (percent) |
v1, V1 |
instantaneous fundamental voltage, average/rms fundamental voltage (V) |
vn, Vn |
instantaneous nth order harmonic voltage, average/rms nth order harmonic voltage (V) |
WTHD |
weighted total harmonic distortion (percent) |
ϕ1 |
phase angle of the fundamental harmonic (degree, or radian) |
1.1.3 Factors and Symbols Used in DC Power Systems
We define the output DC voltage instantaneous value to be vd and the average value to be Vd (or Vd0) [5]. A pure DC voltage has no ripple; it is then called ripple-free DC voltage. Otherwise, a DC voltage is distorted and consists of a DC component and AC harmonics. Its rms value is Vd-rms. For a distorted DC voltage, its rms value Vd-rms is constantly higher than its average value Vd. The ripple factor (RF) is defined as
(1.24) |
where Vn is the nth order harmonic. The form factor (FF) is defined as
(1.25) |
where V0 is the 0th order harmonic; that is, the average component Vd. Therefore, we obtain FF > 1, and the relation
(1.26) |
The form factor FF and ripple factor RF are used to describe the quality of a DC waveform (voltage and current parameters). For a pure DC voltage, FF = 1 and RF = 0.
Symbol |
Explanation (Measuring Unit) |
FF |
form factor (percent) |
RF |
ripple factor (percent) |
vd, Vd |
instantaneous DC voltage, average DC voltage (V) |
Vd-rms |
rms DC voltage (V) |
vn, Vn |
instantaneous nth order harmonic voltage, average/rms nth order harmonic voltage (V) |
1.2 FFT—Fast Fourier Transform
The FFT [6] is a very versatile method of analyzing waveforms. A periodic function with radian frequency ω can be represented by a series of sinusoidal functions:
f(t)=a02+∞∑n=1(an cos nωt + bn sin nωt) |
(1.27) |
where the Fourier coefficients are
an=1π2π∫0f(t)cos(nωt)d(ωt)n=0,1,2,…∞ |
(1.28) |
(1.29) |
In this case, we call the terms with radian frequency ω the fundamental harmonic and the terms with radian frequency nω (n > 1) higher order harmonics. If we draw the amplitudes of all harmonics in the frequency domain, we can get the spectrum in individual peaks. The term a0/2 is the DC component.
1.2.1 Central Symmetrical Periodical Function
If the periodic function is a central symmetrical periodic function, all terms with cosine function disappear. The FFT becomes
(1.30) |
where
(1.31) |
We usually call this the odd function. In this case, we call the term with the radian frequency ω the fundamental harmonic, and the terms with the radian frequency nω (n > 1) higher order harmonics. If we draw the amplitudes of all harmonics in the frequency domain, we can get the spectrum in individual peaks. Since it is an odd function, the DC component is zero.
1.2.2 Axial (Mirror) Symmetrical Periodical Function
If the periodic function is an axial symmetrical periodic function, all terms with sine function disappear. The FFT becomes
(1.32) |
where a0/2 is the DC component and
(1.33) |
The term a0/2 is the DC component. We usually call this function the even function. In this case, we call the term with the radian frequency ω the fundamental harmonic, and the terms with the radian frequency nω (n > 1) higher-order harmonics. If we draw the amplitudes of all harmonics in the frequency domain, we can get the spectrum in individual peaks. Since it is an even function, the DC component is usually not zero.
The spectrum of a periodic function in the time domain is a discrete function in the frequency domain. For a nonperiodic function in the time domain, it is possible to represent it by Fourier integration. The spectrum is a continuous function in the frequency domain.
1.2.4 Useful Formulae and Data
Some trigonometric formulae are useful for FFT:
sin2x+cos2x=1sinx=cos(π2−x)sinx=−sin(−x)sinx=sin(π−x)cosx=cos(−x)cosx=−cos(π−x)ddxsinx=cosxddxcos=−sinx∫sinx dx=−cosx∫cosx dx=sinxsin(x±y)=sinx cosy±cosxsinycos(x±y)=cosxcosy∓sinxsinysin2x=2sin x cos xcos2x=cos2x−sin2x
Some values corresponding to the special angles are usually used:
sinπ12=sin15∘=0.2588cosπ12=cos 15∘=0.9659sinπ8=sin 22.5∘=0.3827cosπ8=cos 22.5∘=0.9239sinπ6=sin 30∘=0.5cosπ6= cos 30∘=√32=0.866sinπ4=sin 45∘=√22=0.7071cosπ4=cos 45∘=√22=0.7071tanπ12=tan15∘=0.2679tanπ4=tan 45∘=1tanπ6=tan 30∘=√33=0.5774tanπ4=tan 45∘=1tan x=1co−tan xtan x=co−tan(π2−x)
1.2.5 Examples of FFT Applications
Example 1.3
An odd-square waveform is shown in Figure 1.4. Find the FFT and HF up to the 7th order, and also the THD and WTHD.
Solution:
The function f(t) is
(1.34) |
The Fourier coefficients are
bn=1π2x∫0f(t)sin(nωt)d(ωt)=2nπnπ∫0sin θ dθ=21−(−1)nnπ
or
(1.35) |
Finally, we obtain
(1.36) |
The fundamental harmonic has an amplitude of 4/π. If we consider the higher order harmonics until the 7th order, that is, n = 3, 5, 7, the HFs are
HF3 = 1/3; HF5 = 1/5; HF7 = 1/7;
The THD is
(1.37) |
The WTHD is
(1.38) |
Example 1.4
An even-square waveform is shown in Figure 1.5. Find the FFT and HF up to the 7th order, and also the THD and WTHD.
The function f(s) is
(1.39) |
The Fourier coefficients are
an=1π2π∫0t(t)cos(nωt)d(ωt)=4nπnπ2∫0cos θ d θ=4sinnπ2nπ
or
(1.40) |
The term sin nπ2 is used to define the sign. Finally, we obtain
(1.41) |
The fundamental harmonic has the amplitude 4/π. If we consider the higher order harmonics until the 7th order, that is, n = 3, 5, 7, the HFs are
HF3 = 1/3; HF5 = 1/5; HF7 = 1/7;
The THD is
(1.42) |
The WTHD is
(1.43) |
Example 1.5
An odd-waveform pulse with pulse width x is shown in Figure 1.6. Find the FFT and HF up to the 7th order, and also the THD and WTHD.
The function f(t) is in the period –π to +π:
(1.44) |
The Fourier coefficients are
bn=1π2π∫0f(t)sin(nωt)d(ωt)=2nπnπ+x2∫nπ−x2sin θ d θ=2cos(nπ−x2)−cos(nπ−x2)nπ=22cos(nπ−x2)nπ=4 sin (nπ2)sin(nπ2)nπ
or
(1.45) |
Finally, we obtain
(1.46) |
The fundamental harmonic has the amplitude 4πsinx2. If we consider the higher order harmonics until the 7th order, that is, n = 3, 5, 7, the HFs are
HF3=sin3x23 sinx2; HF5=sin5x25 sinx2; HF7=sin7x27sinx2
The values of the HFs should be absolute.
If x = π, the THD is
(1.47) |
The WTHD is
(1.48) |
Example 1.6
A 5-level odd waveform is shown in Figure 1.7. Find the FFT and HF up to the 7th order, and also the THD and WTHD.
The function f(t) is in the period –π- +π:
f(t)={2π3≤ωt<2π31π6≤ωt<π3,2π3≤ωt<5π60other−1−5π6≤ωt<−2π3,π3≤ωt<−π6−2−2π3≤ωt<−π3 |
(1.49) |
The Fourier coefficients are
bn=1π2π∫0f(t)sin(nωt)d(ωt)=2nπ[5nπ6∫nπ6sin θ d θ +2nπ3∫nπ3sin θ d θ]=2nπ[(cosnπ6−cos5nπ6)+(cosnπ3−cos2nπ3)]=4nπ(cosnπ6+cosnπ3)
or
(1.50) |
Finally, we obtain
(1.51) |
The fundamental harmonic has the amplitude 2π(1+√3). If we consider the higher-order harmonics until the 7th order, that is, n = 3, 5, 7, the HFs are
HF3=23(1+√3)=0.244; HF5=√3−15(1+√3)=0.0536; HF7=√3−15(1+√3)=0.0383
The values of the HFs should be absolute.
The THD is
(1.52) |
The WTHD is
WTHD=√∑∞n=2V2nnV1=√∞∑n=2HF2nn=√0.24423+0.053625+0.038327=0.1436 |
(1.53) |
DC/AC inverters [1,2] were not widely used in industrial applications before the 1960s because of their complexity and cost. They were used in most fractional horsepower AC motor drives in the 1970s since AC motors have advantages such as lower cost than DC motors, small size, and they are maintenance-free. Because of advances in semiconductor technology, more effective devices such as IGBTs and MOSFETs were produced in the 1980s, and DC/AC inverters began to be widely applied in industrial applications. Currently, DC/AC conversion techniques can be grouped into two categories: pulse width modulation (PWM) and multilevel modulation (MLM). Each category has many circuits that implement the modulation. Using PWM, we can design various inverters such as voltage source inverters (VSIs), current source inverters (CSIs), impedance source inverters (ZSIs), and multistage PWM inverters.
A single-phase half-wave PWM is shown in Figure 1.8.
The pulse width modulation (PWM) method is suitable for DC/AC conversion since the input voltage is usually a constant DC voltage (DC link). Pulse phase modulation (PPM) is also possible, but is not so convenient. Pulse amplitude modulation (PAM) is not suitable for DC/AC conversion since the input voltage is usually a constant DC voltage. In PWM operation, all pulses’ leading edges start from the beginning of the pulse period, and their trailing edge is adjustable. PWM is the fundamental technique for many types of PWM DC/AC inverters such as VSI, CSI, ZSI, and multistage PWM inverters.
Another group of DC/AC inverters are the multilevel inverters (MLIs). They were invented in the late 1970s. The early MLIs were constructed by diode-clamped and capacitor-clamped circuits. Later, other MLIs were developed.
Three important procedures have to be emphasized in this book:
• To categorize existing inverters
• To introduce updated circuits
• To investigate soft switching methods
1.3.1 Categorizing Existing Inverters
Since the number of inverters is large, we have to sort them systematically. Some circuits have not been precisely named, so their functions cannot be inferred from their names.
Many updated DC/AC inverters were developed in recent decades, but not introduced in textbooks. We have to incorporate these techniques in this book and teach students to understand them.
The soft switching technique has been widely used in switching circuits for a long time. It effectively reduces the power losses of equipment and greatly increases the power transfer efficiency. A few soft switching technique methods will be introduced in this book.
1. Luo, F. L. and Ye, H. 2010. Power Electronics: Advanced Conversion Technologies, Boca Raton, FL: Taylor & Francis.
2. Luo, F. L., Ye, H., and Rashid, M. H. 2005. Digital Power Electronics and Applications. Boston: Academic Press Elsevier.
3. Rashid, M. H. 2004. Power Electronics: Circuits, Devices and Applications (3rd edition). Upper Saddle River, NJ: Prentice Hall.
4. Luo, F. L. and Ye, H. 2007. DC-modulated single-stage power factor correction AC/AC converters. Proc. ICIEA’2007, Harbin, China, pp. 1477–1483.
5. Luo, F. L. and Ye, H. 2004. Advanced DC/DC Converters. Boca Raton, FL: CRC Press.
6. Carlson A. B. 2000. Circuits. Pacific Grove, CA: Brooks/Cole.